Other Inputs
SWS-73
 
The SWS-73 indicator is intended for displaying the measurement data sent from the master device over the RS 485 link (Modbus RTU protocol). The display brightness can be adjusted in 8 steps.
SWS-94
 
The SWS-94 indicator is intended for displaying the measurement data and characters defined by user sent from the master device over the RS 485 link (Modbus RTU protocol). The display brightness can be adjusted in 8 steps
SWE-73-S
 
 
The SWE-73 efficiency indicators are low-cost and affordable panel-mounted digital indicators. They are available in three versions: with serial input (-S), current/voltage (-A, description on pages 1.1.3, 1.2.3) and temperature (-T, description on page 1.3.3). The 16-bit A/D converters used in them ensure very high stability and measurement precision. Parameters can be programmed freely through an infrared link or through the RS-485 interface, built-in as a standard. Configuration of the device can also be programmed to the customer's order. The RS-485 interface makes it easy to set up measurement networks in production process monitoring systems, and also to use the indicators as smart, programmable, digital converters of input signals for computer systems. An additional advantage of the device is that its dimensions are small and it can be easily mounted.
SWS-WXXX
 
The SWS-WXXX large-size indicator is intended for displaying any numerical values and user-defined characters set by the RS-485 serial interface link. Program switching into a MASTER mode enables its use as a repeater of displayed information sent from any device featuring the RS-485 / SLAVE link. The display brightness can be adjusted in 8 steps. An infrared control option has been provided for to facilitate the modification of the SWS-WXXX settings without casing removal. The communication with the device is by means of the Modbus RTU protocol. Other (optional) communication protocol with a device featuring RS-485 interface is available on request.
SW-BCD-94
 
The SW-BCD-94 indicator can be used as the indicator output for PLCs to display data in the binary, bcd or byte format or to show typical information transmitted over the RS-485 interface. Depending on the parameter settings, the indicator can display: - digits (0 - 9), with programmable decimal point, - binary data (0 - 9, A - F), showing the statuses of e.g. the address lines, data lines, etc. - various messages and text which can be created on the 7-segment digital displays.
SWS-457
 
The SWS-457 indicator is intended to show any numerical values quoted by the RS-485 link. Users have the possibility of an 8-step adjustment of colour (among others red, yellow and green) as well a 4-step brightness adjustment for the display. The device features a 4-button keyboard for programming basic settings, which for greater security is located under the front cover. In order to make setting changes without unsealing the casing, remote control has been included by means of an (optional) infrared remote control unit. The keyboard on this remote control unit is the same as the device's keyboard (this applies to the type IP67 casing).
 
SWS-W606
 
The SWS-W606 is a simple digital panel indicator intended for displaying any numerical values and characters defined by user (in SLAVE mode only) sent from the master device over the RS-485 serial interface link. The displayed value may be collected from other device (in MASTER mode). The display brightness can be adjusted in 8 steps. The device has 4 buttons being used for main presets programming. To get high protection level, the keyboard is mounted under transparent cover. To allow user to change presets without opening the cover, an IR sensor is mounted. Remote controller keyboard is equivalent to the device keyboard (Note, that IR programmer SIR-15 is not a part of the set. It is an additional equipment). Modbus RTU protocol is used to communication with device. Baud rate is user defined in 1200 ÷ 115200 baud range. It is possibe to order device with other communication protocol using RS-485 interface (special order required).
SWS-W510
 

 
 The SWS-W510 is a simple digital panel indicator intended for displaying any numerical values and characters defined by user (in SLAVE mode only) sent from the master device over the RS 485 serial interface link. The display brightness can be adjusted in 8 steps. The device has 4 buttons being used for main presets programming. To get high protection level, the keyboard is mounted under transparent cover. To allow user to change presets without opening the cover, an IR sensor is mounted. Remote controller keyboard is equivalent to the device keyboard (Note, that remote controller SIR-15 is not a part of the set. It is an additional equipment). Modbus RTU protocol is used to communication with device. The t is user defined in 1200 ÷ 115200 baud range. It is possible to order device with other communication protocol using RS-485 interface (special order required).
SZP-73
 

 
 Name: SZP-73 Power supply: 230V AC ± 10% or 24V DC (non separated) Power consumption: For 230V AC power supply: max. 1,5 VA; for 24V DC power supply: max. 3,5 W Display: LED, red, 4 x 13 mm high Current output: 4-20 mA (PASSIVE), isolated Min. output power supply: 6,5 V Transducer power supply output: 21V DC ± 5V non-stabilized, not insulated from measuring inputs; for 230V AC power supply: max. 25 mA; for 24V DC power supply: max. 100 mA Accuracy: ± 10 mA Stability: typical 50 ppm / °C Operating temperature: 0°C ÷ +50°C Storage temperature: -10°C ÷ +70°C Protection class: IP 40 (front side); IP 20 (case and connection clips) Case: board Case material: NORYL - GFN2S E1 Case dimensions: 72 x 36 x 97 mm Panel cut-out dimensions: 66,5 x 32,5 mm Installation depth: min. 102 mm Board thickness: max. 5 mm

 

©Industrial Temperature Sensors Ltd.      

Ph.00353-45-898164     Fax.00353-45-896521